迷你型電吹風

一、 電吹風 型號：ZF-1238B

二、 產品規格：

1)電壓： 220V-240V 50Hz 或 110V 60Hz ，功率：900W

2)迷你型電吹風:ZF-1238B

3)冷熱風，快慢兩檔

4)直流電機

5)外觀小巧玲瓏

6)產品尺寸:14x16cm

7)有掛環，方便儲存

8)后罩便于移除清洗

9)CCC,CE認證

10)材料:ABS

11)印一色logo

12)可選顏色：紫色，綠色，藍色

13)兩種外殼：1.噴橡皮外殼 2.拋光外殼

三、裝箱尺寸：

1)彩盒尺寸: 17.5X12X8CM

2)外箱尺寸:69.5*40.5*46.5CM

3)數量/箱:80pcs

4)凈重/箱:32 KG

5)毛重/箱:33.5KG

6)20GP數量:17200pcs

7)40HQ數量:41840pcs

四、注意事項：

▲警告:不要在盛水的浴缸、洗臉盆或其他器皿附近使用電吹風。
▲電吹風在浴室內使用，使用后應拔下插頭，因為即使電吹風開關斷開后，接近水仍存在危險。

▲為了增加保護，建議在浴室供電的電氣回路中安裝一個額定剩余工作電流不超過30MA的剩余電流裝置（RCD）。

▲必須使用標準的電源插座，檢查電源電壓必須符合本機的額定電壓。
▲使用時出風口應離頭發或物品60MM以上，當初次使用時，可能會有少量的煙霧出現，屬正?，F(xiàn)象。
▲使用時不要阻塞出/入風口或放置在軟墊上（如床墊、枕頭等），一旦出/入風口阻塞或長時間吹衣服、物品，會造成過熱，當過熱時，內置自動保護會切斷電源，這并不表示損壞，待冷卻后再使用。
▲避免摔落電吹風或讓電吹風受到強烈的撞擊。
▲不要在石油天然氣或其他易燃物品附近使用電吹風。
▲兒童請勿使用,以免發生意外

五、常見故障及處理方法
無動作 ： 電機不轉或線路斷開
電熱絲發紅： 電熱絲有碰絲現象
以上問題均送本公司維修部維修
六、維護保養事項：
★不要用力拉電源線，一旦發現電源線損壞應立即停止使用，為了避免危險，更換電源線須由制造商、其維修部或類似部門的人員來更換，但不可以使用任何方法延伸、駁接電源線。
★應避免頭發及外物進入出風口和入風口，一旦入風口受堵，過熱保護器會自動切斷加熱電源，此時請切斷電源，并去除頭發或外物，等溫度下降后再使用。
★經常保持進風口的干凈，但不要用溶劑或油類擦洗。

1.Mini hair dryer,900W

2.two speed and temperature settings

3.Fashionable appearance

4.CCC,CE approved

5.Hanging loop for easy storage

Mini Hair Dryer

Features:

1)Power supply as 220V-240V 50Hz or 110V 60Hz ,900W

2)Hair Dryer model number:ZF-1238B

3)2 speed and heat settings

4) DC motor

5)Fashionable outlooking design

6) Product size:14x16cm

7) Hanging loop for easy storage

8)Removable end cap for easy cleaning

9)CCC,CE approved

10)Material:ABS

11) print 1 logo on one position

12) Optional Color:purple,blue,green

13) with rubber shell or smooth shell

Packaging details:

1)Color box size: 17.5X12X8CM

2)Carton box size:69.5*40.5*46.5CM

3)Quantity /Carton:80pcs

4) Net weight of carton:32 KG

5)Gross weight of carton:33.5KG

6)20GP:17200pcs

7)40HQ:41840pcs

Delivery time:

1)Lead time for sample:7 days for sample

2)Lead time for delivery:15-20 days for mass production

3)Payment terms:T/T or Western Union

Using the dryer：

1.After washing towel your hair and then use the dryer. Plug in appliance and select the Switch position for the right temperature and airflow.

2.Select the cool shot position. Using cool shot has a good protection on hair,which has been dried and made up.

3.After using, please place the switch at “0”position and then disconnect the dryer.

Important：

1.Connect the dryer to 220-240 volt outlet.

2.Never use in the bathtub,shower, or over a filled sink.

3.Do not use cleaning solutions or abrasives for cleaning the hair dryer.

4.Never lay it down on a humid pillow or blanket when in use.

5.Make sure that the air inlet and air exit grills are free when using the unit.The dryer is protected against overheating.If the air inlet is accidently covered,the dryer will stop automatically.Switch off and allow to cool down,for a few minutes before attempting to restart.

6.Disconnect after use.

7.Children are not aware of potential hazards.Do not allow children to operate this appliance.Make sure they are under supervision whenever they use the hair dryer.

Cleanig your dryer：

Please always disconnect your dryer before cleaning.Do not immerse in water.Protect your dryer unit against dust or oil.From time to time remove dust and hair from the hair inlet grill with a small brush. You can clean your appliance with a slightly damp cloth and dryer it up with a dry cloth provided the hair dryer is disconnected from the mains supply first.

WARNING：

1.Do not use this appliance near water in bathtubs,basins or other vessels.

2.When the hair dryer is used in bathroom,unplug the appliance after use since the proximity of water presents a hazard,even when the hair dryer is switched off.

3.For additional protection the installation of a residual current device (RCD)with a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask yout installer for advice.

4.Do not pull the cord with unnecessary force. Do not damage or modify the cord. If the supply cord is damaged,it must be replaced by the manufactuer its service agent or a similarly qualified person in order to avoid a hazard.